Arizona Bead Blasting FAQs

Welcome to the Arizona Bead Blasting frequently asked question and answer section about glass bead and salt blasting. If you don’t find the answers to your questions below, please call Arizona Bead Blasting at 602.692.4913 and we will do our best to help you.

These FAQs are a way to help and inform you about bead blasting and pool tile cleaning. We hope you find them useful.

What's the white stuff at our waterline?

Dissolved minerals (Calcium) from hard water. As the water laps upon the tile or Pebble Tec, the water evaporates and leaves behind calcium and other minerals. Hence the ugly and unsightly white line.

I'm thinking of cleaning my pool tile line with pumice. Any advice?

Yes. Don’t do it. Cleaning with pumice takes a lot of time and effort. Average swimming pools can take a few weekends. Contrary to what your pool store may say, pumice does scratch the tiles surface. We see this all the time. It’s like looking down the side of a car with a bad wax job. All you see are the swirls. 

How does Arizona Bead Blasting Clean Pool Tile?

This technique again is much like sand blasting, however the air pressure and the media are much different. Kieserite – (Natural mined mineral salt often compared to Epsom) is shot at low pressure. When the salt hits the surface it pops and this force is what frees the calcium from the tiles surface.

Can Pebble Tec be cleaned as well?

Absolutely! Glass beads are best when it comes to blasting Pebble Tec. Not only will glass bead blasting take a fraction of the amount of time that a pumice stone or brush will, it also does a better and more complete cleaning than any other media available.

Do you have to drain the water from my swimming pool?

WE DO NOT EMPTY YOUR SWIMMING POOL! (This process can be performed year round!) Instead, we lower the water level to just below the calcium line (about 6 inches). This gives us enough room to be able to perform the cleaning process and get great results. The water will be drained using one of our industrial grade pumps that will lead to a drain in your front yard or street, depending on your preference and city code.

How long does the Blasting Process take?

The calcium determines how fast we can go. The heavier the build up, the longer the process. Generally speaking an average pool with 1-4 years of build up will take about 2 hours from start to finish.

Won't the glass beads or Epsom salt make a mess in my swimming pool?

No. Glass beads and Epsom salt will sink to the bottom of your pool during the pool blasting process. Once we’re finished blasting, we use a portable vacuum to vac the glass bead or Epsom salt out of your pool. With our pool blasting methods, there’s no mess!

Does Arizona Bead Blasting seal pool tile?

No! All ceramic and porcelain pool tiles are manufactured with a clear glaze to protect the tile from the elements. Many companies are shooting the tile improperly and destroying the glaze. Sealer is than applied on the blasted surface to cover up the damage. Further, once applied the sealer will yellow or turn white after six months due to the UV rays in the sun light. When shot properly the glaze is not damaged and the tile looks near perfect after cleaning.

How long will my pool tiles or Pebble Tec stay clean?

This really depends on how well you maintain your pool chemistry and the source of your water. Typically, your swimming pool will benefit from a weekly maintenance program and a pool tile cleaning service every year.

Do I have to be home during the pool tile cleaning?

You do not have to be home during the cleaning process. All we need is access to your pool and a power source.

What about my kids? My pets?

Although the glass beads and Epsom salt are safe and environmentally friendly, we do ask that you keep people and pets away from the pool during the pool tile blasting process due to the nature of the equipment.

When will I be able to use my pool again?

You will be able to use your pool immediately after the process is complete. However, the water will be cloudy and the level will be down.  For pristine swimming conditions we suggest waiting until the next day.  One eight hour filtration cycle and the water will be crystal clear again.

What People are Saying…

"After years of thinking I could clean my tile on my own, I finally gave up and called AZ Bead Blasting on the recommendation of a friend! The owner was SO professional and friendly and the job he did was far beyond what I expected! My tile looks brand new. I wish I hadn't waited so long to call! I highly recommend them to everyone!!"

− Dave Stevens Scottsdale, AZ

"It was such a comfort to know that Arizona Bead Blasting could not only clean my pool tile, but do so without draining the pool. We were able to swim the same day! Thanks for all your hard work. I'm a believer!!"

− Gail Blanck Carefree, AZ

"AWESOME!! Arizona Bead Blasting was very professional, responded promptly and were extremely knowledgable. We didn't realize our pool tile could look so beautiful again. We are beyond satisfied and will recommend Arizona Bead Blasting's service to friends, family and co-workers."

− Jen Wilson Chandler, AZ

"Thanks Mark for your hard work. Sheri and I are amazed by how beautiful our pool tile looks. We will see you next year!"

− Andy & Sheri Marshall Gold Canyon, AZ